Monitor Manifold Pressure using GReddy Pressure Sensor. 5. Monitor the Multi Switching System Switch to retardadvance IG timing when active. 6. Monitor air fuel ratios using a wide band (0-5V) O2 sensor. 7. Lock unit with a password. 15 B asic Operation without Support Tool Software Without the Supp ort tool soft ware, you can onl y make adjustments using the rotary dials on the front of the unit.Main Harness (included with e-manage unit) Wiring Harness for basic control of the air flow meter and VTEC control.Injector Harness (15900901) Plugs into the e-manage Main Harness to allow control of the ECU injector signal and the use of two sub injectors.Must use Support Tool Software) 1 Ignition Harness (15900901) Enables control of the ECU ignition pulse.
Greddy Emanage Blue Software Software Are UpdatedPlease make sure firmware and software are updated to latest version (1.49). Pressure Sensor with Pressure Sensor Harness (16401301 16401406) Used for monitoring manifold pressure with the e-manage system. This does not replace the factory sensor, but is used only for tuning the e-manage unit. Sensor is a 0-5 volt sensor and 2 Profec e-01 to e-manage pressure sensor harness(15900543) Used to allow the e-manage to monitor manifold pressure through the e-01 pressure sensor reading. AF Sensor Harness (15900912) Used to connect a wide band O2 sensor 0-5 volt analog signal to the e-manage Option port. Used for data logging air fuel ratio while tuning with Support Tool. Adapters Depending on the application, some adapters will be required to be wired into the system. O2 Sensor Adapter shown below) 1. Ignition Adapter 1 (15900906) Used to prevent a check engine light when wiring the Ignition Harness on the Nissan NEO Straight Six (ER34, WGNC34) 3 2. Designed for vehi cles that have a narrow band (0-1V) O2 sensor. Knock Sensor Adapter (15900903) Used for vehicles with very sensitive Knock Sensors. Designed to prevent Ignition Timing retard fr om ECUs that are t oo sensiti ve. M SS Adapter (15900911) Used t o monitor the Multi Switching System activat ion signal and retardadvance igniti on timing when acti vat ed. Water Temp Signal Adapter (15900913) Used t o improve engi ne starting when usi ng larger injectors. Wiring and Setup Wiring Diagram 1. Basic Harness Can be used to control AAV and VTEC Point with rotary dials on the front of the unit. Optional Injector Harness Used to splice into the fact ory inj ect or wires to add injector pulse width. If injector ground is not connected properl y the additi onal injection function will not operat e properl y. Injector channels are connected in order of cyli nder number. Igniti on Harness Used t o adjust ignition timi ng b y intercepting ECU ignition p ulse. Connect ignition channels i n order of engine firing order. Initial Setup Initial setup consists of a few steps to allow t he e-manage to be configured for your applicati on. Initial Set up will consist of: Rotary Switch setting Used to det ermine the vehicle applicati on Jumper Setting Used to adj ust the circuits on t he e-manage hardware to match t he prop er application. To prepare the unit for i nitial set up, you will need to remove the front cover and remove t he hardware from the case. Rotary Switch Setting 1 2 3 1. Set t o determi ne the cylinder number and i gniti on s ystem t ype. Set t o determi ne the air fl ow meter manufacturer. Set t o determi ne the air fl ow meter model. Rotary Switch 1 Setting Information The number of c ylinders and i gnit ion t ype will determi ne the setting for rotary switch 1. Switch 1 0 1 2 3 4 5 6 7 8 9 A B C D E F Cylinder 3 3 4 4 4 6 6 6 8 8 2 ROTOR 2 ROTOR 3 ROTOR Ignition Type DISTRIBUTOR INDIVIDUAL COIL DISTRIBUTOR GROUP FIRE INDIVIDUAL COIL DISTRIBUTOR GROUP FIRE INDIVIDUAL COIL DISTRIBUTOR EXCEPT 4A-GZE EXCEPT 7M-GTE FD3S FC3S JCESE - 12 Rotary Switch 2 and 3 setting information. The manufacturer and air flow meter t ype will determine rotar y switch 2 and 3 sett ings. Jumper Setting Information There are 7 Jumpers used for the e-manage s ystem. ![]() Greddy Emanage Blue Software Upgrade Injector SizeEnables you to upgrade injector size (generally up to 50 larger injector than stock). Upgrade air flow meter to larger size (only on select vehicles) 4. Monitor Manifold Pressure using GReddy Pressure Sensor. Monitor the Multi Switching System Switch to retardadvance IG timing when active. Lock unit with a password. B asic Operation without Support Tool Software Without the Supp ort tool soft ware, you can onl y make adjustments using the rotary dials on the front of the unit.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |